How do you remove concrete from chain link fence posts?

Before attempting to remove the fence posts, remove the fencing and top rail. Clip the metal rings or strips holding the chain link to the posts and roll up the fencing. Lift off the top rail and caps. Dig down along the side of the concrete until you get to the bottom of the post and concrete.

Keeping this in view, how do you remove metal fence posts from concrete?

Start by using your shovel to dig around the steel fence posts and the concrete. This will make it easier for you to remove them later. Dig all the way down to the bottom of the concrete. Wear gloves for digging and then try moving the steel fence posts backward and forward to loosen them a little.

Secondly, can you reuse chain link fence posts? Yes the old posts can be reused, and it would be better to remove the old concrete bases from the posts. To remove the bases from the posts all you need do is hit the base of the post (NOT THE CEMENT) with a 12-16 lb sledge hammer The cement would literally vibrate off the post.

People also ask, how do you remove concrete footings?

Steps in Removing Concrete Deck Footings

Ensure that the structure is supported, remove the footing post if applicable.
Using a spade shovel manually excavate around the footing at least 3/4 the way around and at least 2/3rds of the length of the footing.
Dig until you see the footing wiggle a bit.

How do I get rid of an old fence?

How to Dispose of Old Fence Posts

Ask Your Fence Installation Company. Most fence installation companies will haul your old fencing off for an extra fee.
Find Someone Who Wants Your Old Fence Posts.
Contact the Dump about Construction Waste.
Repurpose the Fence Posts.

How do you remove T bar fence posts?

Begin by rocking the post back and forth to loosen the soil around it.

Option 1

Position a fence post puller next to the T-post to be removed.
With the post puller arm end up, latch the puller's hook beneath one of the nodules on the T-post.
Push the puller arm down slowly and allow the leverage action to do the work.

How long should concrete set for fence posts?

Typically, you can apply some weight to the posts after 4 hours, but it's a good idea to wait at least 24 hours before resuming fence construction. Standard concrete mixes may take up to two hours to set and should cure for 24 to 48 hours before any forces are applied to the posts.

Can you break up concrete with a sledgehammer?

Tool #1: SledgehammerWhen thinking about breaking up concrete, most of our minds jump straight to jackhammer. But you can probably do the work with a metal sledgehammer and a little elbow grease. Sledgehammer is the best tool to use if the slab of concrete is three inches thick or less.

Will a hammer drill break up concrete?

A demolition hammer can't drill because there is no rotation of the bit, which allows the tool to focus on breaking, chipping, and chiseling concrete. They make quick work of pulling up tile and are great for breaking up slabs of concrete.

How do you dissolve concrete?

Spread your phosphoric acid or trisodium phosphate over the concrete area you want to clean first, using a mixture with water that's recommended by the individual manufacturer. Use a brush to scrub the acid into the concrete. These are weaker acids that just might work to dissolve a sufficient amount of concrete.

How much does it cost to remove a fence post?

The average cost to replace posts ranges from an average of $134 to $400. Simple repairs that require little more than repositioning and resetting the posts cost less than completely replacing them. Fallen fence sections are more than unsightly.

Can you reuse concrete fence posts?

Pulling up an existing fence post to reuse can be quite a task. Posts with concrete at the base are the most difficult to remove and reuse because the concrete base is larger than the post, which makes pulling it up through the ground much harder.

How do you keep concrete from rotting?

Caulk around the fence post baseApply high-quality exterior acrylic caulk, or silicone specifically designed to adhere to concrete, at the base of the post. If your cedar wooden fence posts are rotting at the bottom, you need to replace them. The rot probably developed because the posts were installed improperly.

How do you pull up a chain link fence post?

Part 3Removing the Top Rail and Fence Posts

Remove the top rail.
Pull of the post caps.
Dig down to expose the concrete.
Soak the ground around the fence post.
Attempt to remove the post and concrete intact.
Pull out the post with heavy equipment.
Attempt to loosen the fence post.
Cut the fence post as a last resort.

How do you fix a leaning fence post?

Start by breaking up the old concrete footing with a 3-pound sledgehammer and cold chisel. If other posts are also leaning, break the footing around them, too. Drive a stake into the ground to brace the fence, and then screw the stake to the brace with a single screw. Plumb the fence, and then clamp it to the brace.

How do you put a 4x4 in the ground?

Project Instructions

Dig post hole so diameter of the hole is 3 times the width of the post (i.e., the hole for a 4” wood post should be about 12 inches wide).
Add about 6 inches of QUIKRETE All-Purpose Gravel into the bottom of the hole.
Set the post into the hole and attach 2x4 braces to adjacent sides of the post.

How do I delete old mailbox posts?

Remove your mailbox's post from the ground.

Dig around your post with your shovel.
Water the soil inside and around your hole and mailbox post to loosen the soil.
Wiggle and pull at your mailbox post.
Screw your 2-inch by 4-inch wood piece to the mailbox post at a 90-degree angle.

How do you remove a broken fence post from concrete?

The posts are not set in concrete, so just dig them out. Screw lag bolts through a chain into the broken off fence post and then use a vehicle winch/come along/high lift jack to pull the post out. Dig down a few inches and nail or screw a piece of wood to the side of the post then use a fulcrum to pry the post up.